View MC10E131_88314.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
4 Bit D Flip Flop
The MC10E/100E131 is a quad master-slave D-type flip-flop with differential outputs. Each flip-flop may be clocked separately by holding Common Clock (CC) LOW and using the Clock Enable (CE) inputs for clocking. Common clocking is achieved by holding the CE inputs LOW and using CC to clock all four flip-flops. In this case, the CE inputs perform the function of controlling the common clock, to each flip-flop. Individual asynchronous resets are provided (R). Asynchronous set controls (S) are ganged together in pairs, with the pairing chosen to reflect physical chip symmetry. Data enters the master when both CC and CE are LOW, and transfers to the slave when either CC or CE (or both) go HIGH.
MC10E131 MC100E131
4-BIT D FLIP-FLOP
* * * * * * *
1100MHz Min. Toggle Frequency Differential Outputs Individual and Common Clocks Individual Resets (asynchronous) Paired Sets (asynchronous) Extended 100E VEE Range of - 4.2V to - 5.46V 75k Input Pulldown Resistors Pinout: 28-Lead PLCC (Top View)
R3 25 CE3 D3 S12 VEE CC S03 D0 26 27 28 1 2 3 4 5 CE0 6 R0 7 D1 8 CE1 9 R1 10 NC 11 VCCO D2 24 CE2 23 R2 22 VCCO 21 Q3 20 Q3 19 18 17 16 15 14 13 12 Q2 Q2 VCC Q1 Q1 Q0 Q0 S03 S12 CC R1 CE1 D1 Function Data Inputs Clock Enables (Individual) Resets Common Clock Sets (paired) True Outputs Inverting Outputs R0 R CE0 D0 D S Q Q Q0 Q0 D S R Q Q Q1 Q1 S D3 CE3 R R3 D2 CE2 R R2 S D Q Q D Q Q Q3 Q3 FN SUFFIX PLASTIC PACKAGE CASE 776-02
LOGIC DIAGRAM
Q2 Q2
* All VCC and VCCO pins are tied together on the die.
PIN NAMES
Pin D0 - D3 CE0 - CE3 R0 - R3 CC S03, S12 Q0 - Q3 Q0 - Q3
7/96
(c) Motorola, Inc. 1996
2-1
REV 3
MC10E131 MC100E131
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
-40C Symbol IIH Characteristic Input HIGH Current CC S R, CE D 58 58 Min Typ Max 350 450 300 150 70 70 58 58 Min 0C Typ Max 350 450 300 150 70 70 58 58 Min 25C Typ Max 350 450 300 150 70 70 58 67 Min 85C Typ Max 350 450 300 150 mA 70 81 Unit A Cond
IIEE
Power Supply Current 10E 100E
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
-40C Symbol fMAX tPLH tPHL Characteristic Maximum Toggle Frequency Propagation Delay to Output CE CC R S D D Min 1000 310 275 300 300 200 225 450 CLK R, S 400 400 60 275 460 725 300 Typ 1400 600 600 625 550 20 -20 150 750 725 775 775 Max Min 1100 360 325 350 350 150 175 400 400 400 60 480 675 0C to 85C Typ 1400 500 500 550 550 20 -20 150 700 675 725 725 Max Unit MHz ps Condition
tS tH tRR tPW tSKEW tr/tf
Setup Time Hold Time Reset Recovery Time Minimum Pulse Width Within-Device Skew Rise/Fall Time
ps ps ps ps ps ps
1 1
2 20-80%
1. Setup/hold times guaranteed for both CC and CE. 2. Within-device skew is defined as identical transitions on similar paths through a device.
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E131 MC100E131
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E131 MC100E131
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E131/D*
MC10E131/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC10E131

	To Download MC10E131 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .